第1个回答 2012-08-15
One end of the test, the test for 1 h at room temperature (25 ° C ± 5 ° C).
To meet the electronic catalog 3 (6Page)
To meet the electronic properties of the catalog 3 (6Page).
The appearance of damage and degeneration adverse
3. Cycle: 30 cycles (each 1 hour 60 hours (low temperature 30hr high temperature 30hr.))
4 The height of 152cm. Down 19 times (iron)
5 end of the experiment for visual inspection within two hours after washing with distilled water
Surface corrosion from.
Tape adhesive test 2
Tape adhesive test Cutting part Plating face of not have off
2mm 5 line above tape adhesive test 2 back
8 fixed to the rear in the Torque Gage,.
9 fixed to the rear
10.High = 162cm 19 times down the floor (iron)
11 the middle of the push / full gauge
12 for each sample to test 10 products
新! 按住 Shift 键的同时点击并拖动上方的字词即可重新排序。 删除
Google 翻译（企业版）：译者工具包网站翻译器全球商机洞察
关闭即时翻译关于 Google 翻译移动
第2个回答 2012-07-24
我只是在别人的基础上略微修改一个下，都是些小瑕疵，看起来更专业一点而已
1，After the testing, placed it under temperature(25℃±5℃); then test it again. It must fulfil the electronic properties listed in catalog 3(6Page).
2, It must fulfil the electronic properties listed in catalog 3(6 Pages). No physical abuse or bad transformation.
3, Cycle: 30 cycles（one hour for one, totally 60 hours(low temperature 30hr.high temperature 30hr.))
4, Height 152cm, fallen19 times（iron plate）
5, After the testing, clean it with distilled water. Within 2 hours, check its appearance and confirm that there's no erosion and detachment.
6, conduct Tape paste test for two times in a row. After the test, confirm that there's no detachment of plating on the edge of cutting.
7, conduct Tape paste test with 2mm above 5 rows for two times.
8, fixed the tail part to the Torque Gage
9, fixed the tail part.
10, High=162cm 19 times fallen ,floor(iron plate)
11, push/full gauge
12, test ten products for each sample. （最后应该是，每个测试项目，测试10个产品吧）
第3个回答 2012-07-27
1.测试结束后,在常温(25℃±5℃)下放置1小时后 进行测试.
1. After the testing has been finished, leave it at room temperature (25℃±5℃) for one hour, then retest again.
2. 要满足目录3(6Page)的电子特性.
无外观损坏及变性不良
2. Fulfill the requirement of electronic characteristics listed on content 3 (6 page)
No visible damage and bad degeneration
3. Cycle: 30 cycles (各1个小时 总60小时(低温 30hr.高温 30hr.))
3. Cycle: 30 cycles (one hour of high and low temperatures for each cycle, high temp. 30 hours; low temp.30 hours, total 60 hours.)
4. 高度 152cm. 落下19次（铁板）
4. 19 times of drop tests from height of 152 cm. (metal plate)
5. 实验结束后 用蒸馏水清洗后 在2个小时之内 进行外观检查
表面无腐蚀,脱离
5. Wash with distilled water after completion of the experiment, and conduct visual inspection within 2 hours.
No corrosion and peeling on the surface
.
6. Tape 黏贴测试 连续进行2次
Tape 黏贴测试后 Cutting的部分 Plating面 不能有脱落
6. Adhesive tape testing, conduct twice consecutively
There should be no peeling off on the plating surface of the cutting section
7. 2mm 5行以上 tape 黏贴测试 2回
7. Two rounds of adhesive tape testing, with 5 rows of 2mm wide adhesive tapes.
8.把尾部固定在Torque Gage
8. Secure the tail section on Torque Gage.
.
9.把尾部固定
9. Secure the tail end
10.High=162cm 19次 落下 ,地板(铁板)
10. 19 times of drop tests from height of 162 cm., floor (metal plate)
11.把中间 push/full gauge
11. Push/ full gauge in the center
12.每个样品，测试10个产品
12. conduct tests on 10 products of each sample
第4个回答 2012-08-16
1. Test ended, in room temperature (25 ℃ ± 5 ℃) for 1 hour after testing.
To meet the directory 3 (6 page) electronic
2. To meet the directory 3 (6 page) electronic characteristics.
No appearance damage and degeneration bad
3. Cycle: 30 cycles (each 1 hours total 60 hours (low temperature 30 hr. High temperature 30hr.)
4. Height 152 cm. Fall 19 (iron)
5. After the experiment with distilled water after cleaning in two hours for appearance inspection
Surface no corrosion, from.
6. Tape affixes test continuous twice
Tape affixes testing Cutting part Plating surface can't have fall off
7. 2 mm five line above tape affixes test 2 back
8. The tail fixed in Torque Gage.
9. The tail fixed
High = 162 cm 19 fall, the floor (iron)
11. The middle push/full gauge
12. Each sample, test 10 products
第5个回答 2012-08-22
1. Test ended, in room temperature (25 ℃ ± 5 ℃) for 1 hour after testing.
To meet the directory 3 (6 page) electronic
2. To meet the directory 3 (6 page) electronic characteristics.
No appearance damage and degeneration bad
3. Cycle: 30 cycles (each 1 hours total 60 hours (low temperature 30 hr. High temperature 30 hr.)
4. Height 152 cm. Fall 19 (iron)
5. After the experiment with distilled water after cleaning in two hours for appearance inspection
Surface no corrosion, from.
6. Tape affixes test continuous twice
Tape affixes testing Cutting part Plating surface can't have fall off
7. 2 mm five line above tape affixes test 2 back
8. The tail fixed in Torque Gage.
9. The tail fixed
High = 162 cm 19 fall, the floor (iron)
11. The middle push/full gauge
12. Each sample, test 10 products